Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Just about everyone is bound to have their own unique idea involving Installing A Bathtub.
Installing a tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a brand-new one is also a reasonably tough job. If the old tub is easily available, the project can move quickly; if you need to open up a wall surface to remove the old bathtub and position the new bathtub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and set in the brand-new one. See to it you have qualified on your own for the task as well as are comfortable trying it. Rather than hiring a professional to take over a halfway-completed task, it is much better to take into consideration using one before you start. Opportunities are you may require a professional plumber to make tube connections.
This write-up will help you mount a brand-new bath tub in your shower room if you have already gotten a new bathtub as well as do not need to change the setup of your previous supply of water pipelines.
Your tools and also product checklist must consist of the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath must be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to prevent strain on the bathtub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing taps can be quite troublesome due to the limited access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, put the tub in the needed setting. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the tub till the level checks out degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Turn on the water system and also inspect all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the bath tub as well as likewise examine the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the tub must wait up until the tub has been utilized at least when as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind must be attached to the tap ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall in between the bath and also the tiling, causing difficulties with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly available on the market. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about How to Install a Bathtub Yourself, I assumed sharing that excerpt was a great idea. In case you liked our blog entry kindly remember to share it. I am grateful for your time. Please stop by our site back soon.
Schedule Estimate Report this page